People ask me for "the purchasing checklist." There isn't one — not a single one, anyway. Last quarter I handled a quote for Metso C140 jaw crusher wear liners, sourced a replacement kit for an Elvie pump in the mothers' room, and renewed the service contract on the trash compactor behind the loading dock. Same department. Three completely different processes.
The mistake I see junior buyers make (and I made it too) is assuming procurement is procurement. It isn't. Run a six-figure capital equipment purchase through the same workflow as a $300 employee device and you'll either drown the small one in paperwork or wave the big one through on a single quote. Both are bad, just in different ways.
Here's how I split it, and how you can figure out where your purchase belongs.
The three buckets
I sort everything by one question first: what happens if this thing fails or arrives wrong? The answer puts a purchase into one of three groups, and each group gets its own process.
- Bucket 1: Failure stops production or a service line.
- Bucket 2: One employee uses it personally and directly.
- Bucket 3: It has a safety procedure attached, or someone can get hurt operating it wrong.
If a purchase fits more than one, use the stricter process. More on that at the end.
Bucket 1: capital equipment with an engineering spec
This is the Metso C140, the cone crushers, the slurry pumps — anything where operations writes a spec before I write a PO.
I don't pretend to be an engineer. My job in this bucket is the commercial side: comparing quotes on identical terms, confirming spare parts availability, tracking how fast the dealer responds when something breaks. The technical evaluation belongs to the maintenance lead and the plant manager. What I control is whether the paperwork behind their decision holds up.
What I actually check before a PO goes out
Not price first. Uptime first, price second. A primary crusher that's down costs more per day in lost output than most people outside operations realize, so a slightly cheaper quote with a two-week-longer parts lead time isn't cheaper at all. I ask three things of every dealer quote:
- Do you stock wear parts locally, or does everything ship from a regional warehouse?
- What was your lead time variance on the last four orders? (Not the average — the variance.)
- Who is my named contact when the line is down at 2 a.m.?
That third one matters more than it sounds. A dealer network is only worth what it delivers on a bad night.
A mistake I only made once
In 2019 I approved a wear parts order using the model number from an old quote. The part had been revised. It didn't fit. We ate roughly $2,800 in restocking fees and lost the better part of a week. Everyone had told me to confirm the drawing revision, not just the model name. I believed them afterward.
Now the maintenance lead signs off on the part number and revision before I release anything. Not the model — the revision. On the C140, the number in the model name refers to the feed opening width, which is useful context but tells you nothing about which liner revision your particular unit was built with. That detail goes on the quote request now, not on my memory.
On the market share question
Every so often a supplier deck lands on my desk with a slide about global cone crusher market share, Metso versus Sandvik, usually with a nice pie chart and no source. I treat those as marketing, not data.
Published share figures move year to year and depend heavily on how the market is defined — new units only, or including parts and service? If a number is going to influence a real decision, pull it from the manufacturer's annual report rather than a slide. Both companies publish theirs. I also keep competitor comparisons out of our internal evaluation sheets. They're easy to get wrong, and once a comparison is written down, someone will quote it back to you two years later.
Bucket 2: small equipment an employee uses personally
The Elvie pump is the clearest example I have. Nobody in this bucket cares about a torque curve. What matters is whether the person using it can actually use it, whether replacement parts exist six months from now, and whether the purchase survives an expense audit.
Three things I learned the hard way:
Cheap is not the same as low cost. A unit with an odd flange size or a bottle thread that matches nothing else becomes useless the first time a part wears out. Total cost of ownership (i.e., not the sticker price but what you spend keeping it working) is the only number worth comparing.
Vocabulary causes real damage. I once asked a vendor for "a pump" and got a quote for an industrial pump — completely different category, three times the price. We were using the same word and meaning different things. Now I put the model and the use case in the same sentence: "personal-use breast pump for a lactation room."
Claims need paperwork behind them. Per FTC advertising guidance (ftc.gov), product claims have to be truthful and substantiated. When a vendor says "hospital grade," I ask for the spec sheet that proves it. If they can't produce it, the claim doesn't go in my comparison table.
Bucket 3: facility equipment with a safety procedure
Trash compactors and air compressors live here. Both look ordinary. Both can hurt someone.
On the compactor, the question isn't which model — it's whether the lockout procedure is posted, whether anyone has been trained on it, and whether the service contract covers the hydraulic side. A compactor serviced twice a year on schedule is cheaper than one fixed whenever it jams.
On air compressors, "how to use an air compressor" is not a question a manual answers well enough on its own. We require a documented walkthrough before anyone touches the unit, a sign-off, and the rated pressure posted at the point of use. Daily tank draining and monthly relief valve checks go on a checklist with initials. Not because I like checklists, but because moisture in the tank and a stuck relief valve are the two failure modes that actually injure people.
Here's the part that runs against intuition: people assume a cheaper compressor means cheaper maintenance. In my experience it goes the other way. Lower-cost units tend to cycle more, run hotter, and need service sooner — and the electricity cost per cubic foot of air is usually worse. Over ten years, the purchase price is a small fraction of what you spend. The assumption is that you're buying a machine. The reality is that you're buying a decade of service calls and power bills.
Which means the maintenance contract is part of the purchase decision, not something you negotiate afterward. Getting the service terms quoted at the same time as the unit is fairly basic, and we still forget it. (Note to self: this isn't in our standard template. Fix that.)
How to tell which bucket you're in
Three questions, in order:
- If this fails, does output stop? If yes, Bucket 1. Spec first, price second, parts availability always.
- Does one person use it directly and personally? If yes, Bucket 2. Judge it by whether they can keep using it, not by the invoice.
- Is there a procedure someone has to follow to avoid injury? If yes, Bucket 3. Training and service terms belong in the purchase, not after it.
If it lands in two buckets, use the stricter process. A compressor feeding a production line is Bucket 1, not Bucket 3, even though it has a safety procedure attached. An employee-facing device that needs an annual electrical inspection is probably Bucket 3 with a Bucket 2 flavour.
The point of splitting them isn't the paperwork. It's matching the amount of diligence to the size of the consequence. A $300 pump doesn't need three quotes and a service contract. A jaw crusher does. Getting that backwards is how purchasing departments end up both slow and exposed at the same time.
